Autolux UNI/L version Bedienungsanleitung

Autolux ~ Universal Lighting Controller Installation and User Manual for UNI/L version Quick Guide Increase a value. Decrease a value.

10 2.6 REMOTE SWITCH WIRING CONNECTIONS – S1 to S6 Where remote switches are to be connected, two switch options exist: a) Momentary push button /

11 3 OPERATING INSTRUCTIONS 3.1 The buttons The ten buttons have the following functions: Increase a value. Decrease a value. Accept

12 3.2 The display During normal operation the time and day will be displayed. When the user is not programming or inspecting a parameter, the di

13 3.4 Setting user parameters The controller can be set to operate in a variety of modes to suit the application. Press the SET button when in no

143.6 Setting the Auto Mode Auto Mode defines which controller or sensor inputs the zone will respond to when activating the zone relay. Auto Off m

153.7 Setting the Program (on / off times) Each zone relay can be programmed to be active during certain times of the day. Two active periods can be

16 Two timeslots per day are allowed, where each timeslot includes an ON and OFF time. Once a day’s time program has been completed the day icon wil

173.10 Setting the Extend feature The EXTEND key can be used to initiate or extend a temporary override timer. When in Auto-Clock mode, this will o

18Press OK to initiate the extend period. The normal clock display will be replaced with an overtime countdown. While in extend mode the extend peri

193.13 Battery Type & Replacement The real time clock and program information is battery backed up by a lithium coin cell. When mains power is i

2Autolux ~ Universal Lighting Controller Installation and User Manual CONTENTS Introduction ...

204. Engineer Functions. The engineer functions allow you to program various advanced parameters. In order to access the engineer function press and

214.2 Programming the engineering functions All engineer functions are displayed as a code in the first two digits if the display, e.g. C1, t1, t2 a

22 t1 Extend Time Read/Write 06 00 to 60 Extend maximum allowed time in units of 10 minutes, e.g. “09” allows 90 minutes. Setting 00 effectively dis

23 C1 Zone 1 Sensor Assignment Read/Write 00 00 to 63 Sensors assigned to lighting zone 1. (see tables on pages 24 & 25) C2 Zone 2 Sensor Assignm

24 0=settings menu not protected by PIN. P1 PIN Protection Read/Write 00 00 to 01 1=settings menu protected by PIN. P2 PIN Number Read/Write 0000 000

25Add all values in column four to produce the variable to be programmed for each zone in Engineering Functions C1 to C6. Check results in the table

2648 No No No No Yes Yes 49 Yes No No No Yes Yes 50 No Yes No No Yes Yes 51 Yes Yes No No Yes Yes 52 No No Yes No Yes Yes 53 Yes No Yes No

27

28 Document reference: Autolux ~ Universal Lighting Controller Instructions - Issue 1 – 1st June 2006

3Autolux ~ Universal Lighting Controller Installation and User Manual INTRODUCTION This manual describes the Installation and Operation of the Auto

4 1.3 Electrical Specifications The power supply is SELV isolated, therefore all remote sensor and remote switch wiring to the control does not need

52 INSTALLATION INSTRUCTIONS 2.1 Mounting the Control Assembly Ensure that the controller is installed no less than 1.5m above the floor level. Th

6The housing consists of a two part plastic moulding held together by four screws. Plugs are supplied to cover the screws following installation.

7 2.2 General Wiring Specifications Connect as shown below. A suitably qualified person must make all wiring connections. Please refer to the follo

82.3 WIRING CONNECTIONS External connections are by 27 screw terminals as follows: Screw terminals are 7.5mm and 5mm spacing rising clamp style wit

9 2.4 OCCUPANCY SENSOR WIRING CONNECTIONS – S1 to S6 Where occupancy detection is required, a range of BlueWave sensors are designed for use with th